FUNDAMENTAL PLUMBING TIPS FOR BATHTUB INSTALLATION

Fundamental Plumbing Tips for Bathtub Installation

Fundamental Plumbing Tips for Bathtub Installation

Blog Article

Estimate Free

We have discovered the article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the web and decided it made perfect sense to share it with you on this page.


Tools You Need to Install a New Bathtub
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move easily; if you have to open a wall surface to get rid of the old tub and position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also set in the new one. Make certain you have actually certified on your own for the task as well as fit trying it. Instead of employing a contractor to take over a halfway-completed task, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will certainly aid you install a new tub in your shower room if you have currently gotten a new bathtub and do not need to transform the arrangement of your previous water pipes.
Your devices and material list should make up the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The process of removing the existing faucets can be quite troublesome due to the restricted gain access to that is typically the case.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
    Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next off, place the faucet in the placing opening in the bath/basin ensuring that the washing machines are in area in between the faucet and also the sink. Safeguard the tap in position with the manufacturer provided backnut. When the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The previous kind needs to be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Mounting the Bath tub


    Utilizing the two wood boards under its feet, position the bath tub in the needed placement. The wood boards are handy in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
    The following objective is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub until the level reads degree.
    To mount faucets, fit the bottom of the furthest adaptable tap connector to the suitable supply pipeline by making a compression join; then do the very same for the various other faucet.
    Activate the supply of water as well as inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill the bathtub as well as additionally examine the overflow outlet as well as the regular outlet for leakages.
    Ultimately, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub ought to wait until the bath tub has actually been used at the very least once as this will resolve it right into its last position.

    Preparing for the Installment


    Firstly, the sustaining structure supplied with the bathroom ought to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to stop stress on the tub.
    Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final setting.

    Tiling Around the Bath tub


    In the area where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, triggering the water to pass through the wall between the bathroom and also the tiling, bring about difficulties with moisture and also possible leaks to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can split fairly very early if you do not think about this movement before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is suggested to fit the tiles using waterproof or water resistant sticky and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    Do you enjoy reading about Installing A Bathtub? Try to leave a remark directly below. We would be pleased to find out your reactions about this review. Hoping to see you back again soon. Sharing is caring. You just don't know, you will be helping someone out. Thanks a lot for your time spent reading it.


    Certified experts available.

    Report this page